FREE BOOKS

Author's List




PREV.   NEXT  
|<   358   359   360   361   362   363   364   365   366   367   368   369   370   371   372   373   374   375   376   377   378   379   380   381   382  
383   384   385   386   387   388   389   390   391   392   393   394   395   396   397   398   399   400   401   402   403   404   405   406   407   >>   >|  
earance, but also their insulating properties. [Illustration: Ceiling-Cord Holder] Several of them can be used along a line, as shown in Fig. 2. --Contributed by M. Musgrove, Boissevain, Man. ** Support for Double Clotheslines [318] Anyone using a double clothesline over pulleys will find the arrangement shown in Fig. 1 for supporting the [Illustration: Holder on a Clothesline] lower line quite convenient. The support is made of a piece of 3/4-in. square or round wood which has a screw-eye turned into each end. The line is run through these screw-eyes as shown in Fig. 2. --Contributed by W. W. UpDeGraff, Fruitvale, Cal. ** Hot Pan or Plate Lifter [318] Unless a person uses considerable caution, bad burns may be suffered when taking hot pies from an oven. If one reaches in and takes hold of the pie pan with a cloth, the arm is liable to touch the oven door and receive a [Illustration: Lifter on Pie Pan] burn. To obviate this, I made the device shown in the sketch for lifting hot pie pans and plates. The handle is of pine about 18 in. long, and the two loops are made of heavy wire. The ends of the first loop of wire are put through the handle from the back, as shown, and then bent so as to stand out at an angle. The second loop is hinged to swing free on the opposite side of the handle. In use, the hinged side of the loop is dropped under one edge of a plate or pan and the rigid loop is then hooked under the opposite side. The weight of the pan or dish draws the loops together and there is little or no danger of a spill. The same lifter will pick up any size of plate or pan from a saucer to the largest pie plates. --Contributed by E. J. Cline, Ft. Smith, Ark. ** Weighting Indian Clubs [318] An ordinary Indian club can be fixed so that different weights may be had [Illustration: Indian Club] without changing clubs. Each club is bored to receive lead washers which are held in place by a spiral spring. A bolt is run through from the handle end and fastened with a round nut. The lead washers and spring slip over the bolt as shown in the illustration. Changing the number of washers changes the weight of the club. --Contributed by Walter W. White, Denver, Colo. ** Venting a Funnel [318] When using a tight-fitting funnel in a small-neck bottle, trouble is usually experienced by the air causing a spill. This can be easily remedied by splitting a match in half and tying t
PREV.   NEXT  
|<   358   359   360   361   362   363   364   365   366   367   368   369   370   371   372   373   374   375   376   377   378   379   380   381   382  
383   384   385   386   387   388   389   390   391   392   393   394   395   396   397   398   399   400   401   402   403   404   405   406   407   >>   >|  



Top keywords:

handle

 

Contributed

 
Illustration
 

Indian

 
washers
 

weight

 

receive

 

spring

 

plates

 

opposite


hinged

 
Lifter
 

Holder

 

splitting

 
remedied
 
easily
 
saucer
 

largest

 

dropped

 
hooked

danger
 

lifter

 

Changing

 

number

 
trouble
 
illustration
 

fastened

 

Walter

 

fitting

 

Funnel


bottle
 

Denver

 

Venting

 

spiral

 

ordinary

 

funnel

 

Weighting

 

causing

 

weights

 
experienced

changing

 
convenient
 
support
 

arrangement

 

supporting

 
Clothesline
 

square

 
UpDeGraff
 

Fruitvale

 
turned