FREE BOOKS

Author's List




PREV.   NEXT  
|<   81   82   83   84   85   86   87   88   89   90   91   92   93   94   95   96   97   98   99   100   101   102   103   104   105  
106   107   108   109   110   111   112   113   114   115   116   117   118   119   120   121   122   123   124   125   126   127   128   129   130   >>   >|  
ir taper ends. 2. Cut notches half-way through KK, at about 20 to 25 inches from each end; then turn up the notched portions, and you have stem, keel and stern, all in one piece, as in fig. 2. [Fig 1 and Fig 2 sketches]. 3. Stake out the ground, according to the size your boat will cover, by driving eight strong pointed stakes of wood into the ground; to these lash four cross (willow-tree) sticks, notched in two places, so that each of these four willows shall form two knees, as well as run across the bottom of the boat. 4. Bent two more main willows for gunwales for the boat, and two more for bottom rails. Each separate stick, as will be perceived by fig. 3, is lashed in five different places, and the keep in eight places. [Fig 3 and Fig 4--sketches as described]. The main framework being now completed, loosen it from the stakes driven into the ground. 5. Fasten a large number of little slender willow-twigs between each of the main cross-knees, as shown by the thin lines in fig. 3. It is then fit for covering. Lift it up like a basket, and turn it topsy-turvy. 6. Kill two bulls, skin them, and in skinning be careful to make your cuts in the skin down the rump to the hock of the animal, and down the brisket in front of the fore-leg to the knee, so as to have your skins as square as possible (fig. 4). Cut off the heads, and sew the skins together at the nape of the necks; and, while reeking, cover the wicker-work, turning them over it, the hairy side inwards, and fasten it all round by means of skin-cords. Cut holes with a knife round the edges, to pass the cords through, as you lash up to the top-rails of the boat. 7. Leave it 24 hours in the sun; cover the seam where the skins are sewn together, with melted fat, and the boat is fit for use. Bark Boats.--"From a pine, or other tree, take off with care the longest possible entire portion of the bark; while fresh and flexible, spread it flat as a long rectangular sheet; then turn it carefully up at the sides, the smooth side outwards; sew the ends together, and caulk them well. A few cross-sticks for thwarts complete this contrivance, which is made by an American Indian in a few hours, and in which the rapid waters of the Mackenzie are navigated for hundreds of miles. Ways of strengthening the structure will readily suggest themselves. The native material for sewing is the fibrous root of the pine." ("Handbook for Field Service," Lieut.-Col. Lefroy.)
PREV.   NEXT  
|<   81   82   83   84   85   86   87   88   89   90   91   92   93   94   95   96   97   98   99   100   101   102   103   104   105  
106   107   108   109   110   111   112   113   114   115   116   117   118   119   120   121   122   123   124   125   126   127   128   129   130   >>   >|  



Top keywords:
places
 

ground

 

bottom

 

sticks

 

stakes

 

willows

 

willow

 
notched
 

sketches

 
melted

fasten

 

inwards

 

turning

 

longest

 

strengthening

 
structure
 

readily

 
suggest
 

waters

 

Mackenzie


navigated

 
hundreds
 

native

 

Service

 

Lefroy

 

Handbook

 

material

 
sewing
 

fibrous

 

Indian


rectangular
 

carefully

 
spread
 

portion

 

flexible

 

smooth

 

contrivance

 

American

 

wicker

 

complete


outwards

 

thwarts

 

entire

 
covering
 
driving
 

strong

 
pointed
 

gunwales

 

lashed

 

perceived